PROCUREMENT · GRADE AND BATCH CHECKS

TDS, SDS and COA: Paper Chemical Buying Checklist

Match the offered grade, safety information and batch records before moving from a trial to a production order.

Three documents answer different questions

TDS · PRODUCT AND APPLICATION

What grade is being evaluated?

Use the technical data sheet to identify the offered product and review its published properties and application guidance. Check whether each value is typical, a range or an agreed specification limit. A typical value should not automatically become a batch acceptance limit.

SDS · HAZARDS AND HANDLING

How should the product be handled?

Match the safety data sheet to the product identifier. Review hazards, handling, storage and exposure-control information with the mill’s safety team. An SDS is not a certificate that the product meets the required paper performance.

COA · BATCH INFORMATION

Which batch does the record describe?

When a certificate of analysis is available or required for the purchase, match its product and batch identifiers to the shipment. Review the reported tests, results and limits. Confirm which purchase criteria are actually tested rather than assuming every TDS property appears on the certificate.

PURCHASE SPECIFICATION · AGREEMENT

What will be accepted?

Agree the grade, required properties, methods and limits before placing the order. Keep commercial terms and mill-trial acceptance separate from batch quality checks. Confirm the documents that can be supplied for the particular grade and destination.

Document titles and formats vary by supplier. Use the content and product identity, not the acronym alone, to decide what each document establishes.

Make the comparison like for like

Identity and revision

Record the supplier, product name, grade code and document date or revision. If a label, quotation and document use different identifiers, ask for the mapping before accepting them as the same grade.

Property and measurement basis

For viscosity, request the method, temperature and instrument settings where applicable. For pH, distinguish the supplied product from a specified dilution. For solids, record the method and whether the quoted figure is a typical value or a limit. Do not compare figures with different bases as if they were equivalent.

Product versus process

Product solids content is not an addition rate. A product-solution pH is not necessarily the required process-water pH. Keep the product specification, preparation procedure and mill operating conditions in separate fields.

Batch versus application result

A batch result within an agreed specification does not by itself establish compatibility with a coating formulation, furnish or water-treatment program. Use the relevant mill trial to assess application performance.

Keep one record from sample to order

  1. Before the trial: identify the proposed grade and current documents, define the process question and agree the trial measures.
  2. At receipt: record the product identifier, batch or lot number shown on the label, receipt date and visible packaging condition. Clarify any mismatch before use.
  3. During evaluation: retain the sample identity with test conditions, baseline observations and results.
  4. Before a production order: check that the quotation identifies the intended grade and the agreed specifications, packaging and documents. Resolve substitutions explicitly rather than assuming a family name is sufficient.

For the operating plan and application-specific observations, use the Paper Chemical Trial Planning Guide.

Apply the checklist to your process

Questions before ordering

Can an SDS replace a technical specification?

No. Use the SDS for product hazard and handling information. Confirm the technical purchase criteria separately for the offered grade.

Does a COA prove food-contact or drinking-water suitability?

Not by its title alone. Identify the exact intended use and request the relevant evidence for that grade and destination. Do not infer an approval from a general analysis certificate.

What if a website and a TDS show different values?

First check the grade and revision, then the test method and reporting basis. Ask the supplier which specification applies to the proposed order. Do not combine the two ranges into a new specification.

Reference examples

The OSHA SDS information framework describes product identification, hazards, handling and storage sections. It is a U.S. reference, not a statement of requirements for every destination.

Dow’s EVOQUE 3390 TDS illustrates why typical properties and specifications must be distinguished. Sigma-Aldrich’s COA document lookup illustrates batch-based document identification. These are document-format examples, not Aupha Chem product data or evidence of product equivalence.

Request documents for the grade you need

Send the product or application, intended grade, destination and the properties or documents needed for your review. Availability and scope of documents should be confirmed for the proposed supply.

Request Product Information